| der Luftkühlers http://www.dlkweb.org/phpBB3/ |
|
| Torque-meister Tool question http://www.dlkweb.org/phpBB3/viewtopic.php?f=10&t=5911 |
Page 1 of 2 |
| Author: | Claymore [ Thu Aug 15, 2013 5:57 am ] |
| Post subject: | Torque-meister Tool question |
I am using this thing to install the flywheel gland nut. Do you just use a torque wrench and torque to spec? I understand it is a torque multiplayer. Only thing I could find on line is to divide torque spec by 9 to get proper torque wrench setting. Is this correct? 
|
|
| Author: | kostya.lyt [ Thu Aug 15, 2013 6:43 am ] |
| Post subject: | Re: Torque-meister Tool question |
On mine, it's cast into the body of the tool. It's somewhere along the lines of 9-10 times multiplication. |
|
| Author: | tommiebsmith [ Thu Aug 15, 2013 6:47 am ] |
| Post subject: | Re: Torque-meister Tool question |
Yea.. I usually dab a little oil or grease on the small gear shaft that is for the flywheel teeth part.. I always think that the friction will mess with the torque reading . but basically you need a torque wrench.. and a 7/16 socket.. torque to about 40 ftlbs ... make sure the flywheel O ring is installed.. and the rear main is fully seated.. after torquing it down.. recheck your endplay.. need a flywheel lock also. |
|
| Author: | tommiebsmith [ Thu Aug 15, 2013 6:48 am ] |
| Post subject: | Re: Torque-meister Tool question |
kostya.lyt wrote: On mine, it's cast into the body of the tool. It's somewhere along the lines of 9-10 times multiplication. Yes it is nine |
|
| Author: | Claymore [ Fri Aug 16, 2013 11:28 am ] |
| Post subject: | Re: Torque-meister Tool question |
Think I got it done. Thanks, guys for the help. |
|
| Author: | mk-Zero [ Sat Aug 17, 2013 11:01 am ] |
| Post subject: | Re: Torque-meister Tool question |
Those are great tools! Most guys dont have a torque wrench that goes that high, so that thing really comes in handy. |
|
| Author: | Chisel_86 [ Sun Jan 05, 2014 7:58 pm ] |
| Post subject: | Re: Torque-meister Tool question |
Does anyone know if the torque tool fits the 5x130 pattern? |
|
| Author: | ConcreteAce [ Sun Jan 05, 2014 8:15 pm ] |
| Post subject: | Re: Torque-meister Tool question |
Chisel_86 wrote: Does anyone know if the torque tool fits the 5x130 pattern? No only VW bolt patterns. bet you could build an adapter though. |
|
| Author: | Chisel_86 [ Sun Jan 05, 2014 8:54 pm ] |
| Post subject: | Re: Torque-meister Tool question |
Dang. Ok thanks. My screwdriver tip broke off inside the rear drum when I was trying to adjust the shoes. Now there's a horrifying grind/squeal...  Yeah, go ahead and laugh it up, lol |
|
| Author: | Dlicious [ Sun Jan 05, 2014 9:16 pm ] |
| Post subject: | Re: Torque-meister Tool question |
Chisel_86 wrote: Dang. Ok thanks. My screwdriver tip broke off inside the rear drum when I was trying to adjust the shoes. Now there's a horrifying grind/squeal... Yeah, go ahead and laugh it up, lol ....you aren't the first person this has happened to....Sucks you have to tear it all apart to fix it. |
|
| Page 1 of 2 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|