Beetleluvr's 56

mk-Zero · **Posted:** Fri May 30, 2008 8:34 am

Hopefully its something simple. Let me know if you need any help

beetleluvr · **Posted:** Fri May 30, 2008 8:41 am

mk-Zero wrote:

Hopefully its something simple. Let me know if you need any help

Thanks Brian. I will give you a shout if I see something that I cannot figure out.

69vduber · **Posted:** Fri May 30, 2008 12:40 pm

I had a similar problem with my sons a few years ago. Turned out to be oil cooler seals ... I was able to get to it without pulling the engine... take the deck lid off and pull the dog house off... Hope it is less than that.

good luck.

beetleluvr · **Posted:** Fri May 30, 2008 1:17 pm

69vduber wrote:

I had a similar problem with my sons a few years ago. Turned out to be oil cooler seals ... I was able to get to it without pulling the engine... take the deck lid off and pull the dog house off... Hope it is less than that.

good luck.

Thanks....hopefully the problem will be an easy fix.

beetleluvr · **Posted:** Thu Jun 05, 2008 7:54 pm

Well, I got out & worked on finding the oil leak problem this evening. Turns out it was the oil pressure sending unit needing tightening up. It was not an easy leak to find

. In the process, I tightened a few nuts and bolts that were in need of some attention. I also discovered a few new problems. I have a small leak in my manifold and can see where my exhaust may need some repair or I need to find a replacement. I may be able to use some JB weld until I can take it off to braze or find a replacement.

Anyhow, I am good to go now :thumbs:

.

gostros · **Posted:** Thu Jun 05, 2008 9:18 pm

beetleluvr wrote:

Well, I got out & worked on finding the oil leak problem this evening. Turns out it was the oil pressure sending unit needing tightening up. It was not an easy leak to find

. In the process, I tightened a few nuts and bolts that were in need of some attention. I also discovered a few new problems. I have a small leak in my manifold and can see where my exhaust may need some repair or I need to find a replacement. I may be able to use some JB weld until I can take it off to braze or find a replacement.

Anyhow, I am good to go now :thumbs:

.

good news Ben!

EAnderson · **Posted:** Thu Jun 05, 2008 9:22 pm

gostros wrote:

beetleluvr wrote:

Well, I got out & worked on finding the oil leak problem this evening. Turns out it was the oil pressure sending unit needing tightening up. It was not an easy leak to find

. In the process, I tightened a few nuts and bolts that were in need of some attention. I also discovered a few new problems. I have a small leak in my manifold and can see where my exhaust may need some repair or I need to find a replacement. I may be able to use some JB weld until I can take it off to braze or find a replacement.

Anyhow, I am good to go now :thumbs:

.

good news Ben!

Ditto

mk-Zero · **Posted:** Thu Jun 05, 2008 10:58 pm

Good job bro, glad you got it fixed! :thumbs:

psychosquirrel · **Posted:** Fri Jun 06, 2008 8:42 am

You are supposed to take pictures, this is Like Pre School, we need visual aid's

beetleluvr · **Posted:** Fri Jun 06, 2008 9:11 am

psychosquirrel wrote:

You are supposed to take pictures, this is Like Pre School, we need visual aid's

Damn...forgot. I will take a picture of the manifold with the hole in it and take a picture or two when I remove it and install the new one :thumbs:

.....if I remember :lol:

.

Beetleluvr's 56

Who is online